Dumid

I have tried it and it certainly did not minimise my power purchases. I have since reverted to my manual settings

Hi Guys I have 3 x Powerbox Pro batteries in Parallel. I note the instructions are to open the slave batteries to set the DIP switches of their master modules to slave setting 1. My question is how can I open the batteries when the warranty is voided if the warranty sticker is broken, which will happen if I open the batteries. I am connected to a 12kw 3 Phase Deye Inverter. I can confirm, like other users that the cable that comes with the inverter may not be suitable for BMS comms. I used one for my Internet router.

Hi all. I too had the same issue and have had back and forth emails with Deye technicians. I think I may have resolved it now as I have now beat my previous record of 36 hours uptime. This is what I did(from my mobile phone) 1.Connect direct to the logger via wifi. Allow connection without Internet access when propmpted 2. Enter 10.10.100.254 username admin password admin 3. Reset the logger 4. Run the Wizard and scan the available networks, select your intended connection network and take note of the channel that your Internet router is using. Click next https://pro-cs.udeskcs.com/ticket_reply/tid30244/wifi data logger configuration_1716443478164_2pwz5z.pdf?Expires=1747979482&OSSAccessKeyId=bPexlr6MCcadDhfu&Signature=lE0c3%2FZ84M75JHVPm3p0C6nm8EI%3D 5. Enter the password to your Internet router and select " Enable" for automatic IP address 6. Click next, then OK on next screen 7. Logger will restart. Connect again to logger and Log in to 10.10.100.254 8. Under "Status">"Remote and server Information" , server A should now say connected. The left green light on your logger should be constantly green. 9. If 8 has worked then log onto your wifi router. Find where to change the Channel as observed in point 4 above. By default the router says Auto but now change to the channel where a working connection was possible. 10. Change IP address obtain to "Disabled" 11. You may need to connect once more to logger directly and then select restart(not reset). Wait a minute or two for connection to be re-establushed. Confirm with green light on logger or step 8 above. All the best!

Hi all. I too had the same issue and have had back and forth emails with Deye technicians. I think I may have resolved it now as I have now beat my previous record of 36 hours uptime. This is what I did(from my mobile phone) 1.Connect direct to the logger via wifi. Allow connection without Internet access when propmpted 2. Enter 10.10.100.254 username admin password admin 3. Reset the logger 4. Run the Wizard and scan the available networks, select your intended connection network and take note of the channel that your Internet router is using. Click next https://pro-cs.udeskcs.com/ticket_reply/tid30244/wifi data logger configuration_1716443478164_2pwz5z.pdf?Expires=1747979482&OSSAccessKeyId=bPexlr6MCcadDhfu&Signature=lE0c3%2FZ84M75JHVPm3p0C6nm8EI%3D 5. Enter the password to your Internet router and select " Enable" for automatic IP address 6. Click next, then OK on next screen 7. Logger will restart. Connect again to logger and Log in to 10.10.100.254 8. Under "Status">"Remote and server Information" , server A should now say connected. The left green light on your logger should be constantly green. 9. If 8 has worked then log onto your wifi router. Find where to change the Channel as observed in point 4 above. By default the router says Auto but now change to the channel where a working connection was possible. 10. Change IP address obtain to "Disabled" 11. You may need to connect once more to logger directly and then select restart(not reset). Wait a minute or two for connection to be re-establushed. Confirm with green light on logger or step 8 above. All the best!