vwykj

Good Day I have 4 x Pylontech Us3000 connected to my 8Kw Deye inverter. Can I connect a 5 battery or is there a limit to a Single converter?

I have a question...I have 4 batteries in my bank...Must i disconect each battery before the update and reconnect it back to bank...Or can I upgrade firmware even if batteries is still connected as bank?

I have a question...I have 4 batteries in my bank...Must i disconect each battery before the update and reconnect it back to bank...Or can I upgrade firmware even if batteries is still connected as bank?

I have a question...I have 4 batteries in my bank...Must i disconect each battery before the update and reconnect it back to bank...Or can I upgrade firmware even if batteries is still connected as bank?

Good Day I need some assistance. I have a Deye 8Kw hybrid inverter with 4 x Pylontech 3000 batteries. What can I set the max charging current Amps to the batteries. I know the spec sheets shows 37A for single battery but according to me it is a 4 battery bank that means it can be set to 4 x 37A = 148 minus 1 becasue the inverter will dist it between the 4 battery to bring it to 37A per battery....Is this statement correct. Currently it is set at 50A...It it is taking the whole day to charge even if battery bank is only discharge to 50%. See attached

Same one I used. I have also used the one called [email protected], no results 🤔 Thanks again

Very Strange, I mailed them with 4 mails already since last week regarding my order and no response. I`m getting worried now. Thanks for response

Jacques.. My question is. do they still exist. I have placed order and paid for software and cables. Did not received any comms from them. Do you have a number I can phone them please. Thanks Jacques 0827446606

Jacques.. My question is. do they still exist. I have placed order and paid for software and cables on the website. Did not received any comms from them. Do you have a number I can phone them please. Thanks Jacques 0827446606

Jacques Does this still exist..I have purchase the app, with the cables etc...But I do not get any response from them.. Via mail... Jacques

@wolfandy Good Day I have another question please. I see my 3 pylontech cycles differ. Is it ok. My primary battery is at 207, the rest is at 203 and 202. I can say the two lower ones do pick up on cycles. Or must I change the batteries around abit? Thanks

Good Day I have another question please. I see my 3 pylontech cycles differ. Is it ok. My primary battery is at 207, the rest is at 203 and 202. I can say the two lower ones do pick up on cycles. Or must I change the batteries around abit? Thanks

@Coulomb This happens two weeks ago, and I had a concern it could have been the settings. The installer said it was a eskom surge but I was not 100% convinced. It is fixed now, The MB was replaced and the PV card was replaced. I have changed all the settings to your recommendations above in the post. I have also changed the program 2 back to 50A on both the Master and the Slave Inverters. @wolfandy Thanks for your feedback as well. My setup is as follows: Two Inverters setup in PAL mode 18 x 330V Canadian panels setup as 9 to Master inverter and 9 to the Slave Inverter. 3 x Pylon US3000B Plus 3.5 KWh Li-Ion Battery connected in a stack Yes my Raspberry with the ICC software do have a pylontech communication cable connected to the batteries console port to read the battery information. So that is why my other concern is the ICC software shows the batteries charge to 101% and not sure if I must be worried about it as @Bloubul7 indicated it is a calculation issue. Thanks for everyone`s feedback much appreciated. I`m not a expert just a user and I trying to do some research on it and getting your experts input to understand everything Thanks Jacques

@Coulomb@Bloubul7@wolfandyThanks for your assistance. Much appriciated. Is I had a problem where both inverters faild at same time. The master inverter MB failed and Slave the PV card. So was not sure if it was maybe a setting on the mercer axpert 5k inverters.

@Calvin@Coulomb. What wil be the best setting be for setting 1. SBU or SOL? Thanks Jacques