Sonoff Africa

Hi, how are you . Is that directyl on ewelink? It should us the voltage and current to work watts.

Hi All you need to do is just go into the settings of the Sonoff mini and change the trigger mode into follow mode and it should solve the problem. If it doesn’t solve the problem there could be a few other configurations we can gladly run through. There is also other causes i.e. if the inverter runs flat or is switching the load's and Eskom does load shedding or inverter is going to bypass and does not switch back quick enough creating power interruption depending on the invertor. We been testing and making small changes to the Loadshedder and have a hit rate of 99 out of a 100 on the current version v4 of the Loadshedder. Welcome to give me a call 0823793860 and we can go over some of the setting if the above does not solve the problem. We have it at the point that it will sync itself back into the correct state after one Eskom shedding cycle. Aleks

Congratulations @PsyWulf Just inbox me your address and I will send you the Tracking number. Aleks

Hi It’s our pleasure and sometimes we might be slow to respond due limited time. Aleks

Hi How are you? Yes it will definitely work, just need to be carefull as the is a usb powerd device 5 volts but it dose have a sensor to read the state of the gate. Aleks

Hi We unfortunately don’t have a certified CB yet and I can wait till Sonoff one day bring them out. I am happy that there is a lot of good hardware out there that works with eWeLink which really does help and simplifies the configuration. Aleks

Hi I would like to help but when it comes to solar installations I get an installer as it’s not my strong point at all. Aleks

Hi D1 dimmer and ghosting is a very common problem this is the reason we say on our website we do not support them locally/ But I will gladly help you with a fix. Firstly what happens is the D1 was designed overseas where they don’t have load sheading yet, they would plug in the dimmer and within the first 5 seconds it you push a button on the remote and all the functions are auto programed. The problem with that is every time there is load sheading it can do that for 16 remotes x 8 bottoms and sooner or later it will ghost. If you take your remote close to the dimmer and press the bottom left hand side button and hold for 10 Seconds till it beeps. Than will delete all the frequency’s and the ghosting will stop and your remote will also stop working. Try that for a day or 2 see if stays of and just use the software. The after that you can add your remote by cutting power to it and power it up push a button. Then your remote working again. If it starts Ghosting again will have to do a mode to a Wi-Fi dimmer only. Do you have a inverter? Let me know how it goes. Aleks

Hi @Anarchy05 I just wanted to get a few more details about the logout. I know with some of the new updates and batter saving you have an option to kill the app or to just put it to sleep. I would just select the app as a test set to always run in background and with full permissions ie location permission set to always. Let’s see if it helps. Let me know what phone you are running and version. Aleks

Hi We are going for a few drinks at Urban Oaisus on corne of Witkoppen and Church from 2:30 pm please feel free to join us, I will definatly be quiet a few. You are all welcom th place is quiet small but feel free to pop in, we will be wearing Sonoff shirst its a completly informal event. Aleks

Hi Yes we do it would be the Sonoff Dual R3 it is a 22 volt systems with inter lock Aleks

Hi 1. The Gate controller on our site, I would configure it first at your desk and just make sure you have it working in the eWeLink app and Alex and that you can hear the click noise as you push the button in the app. 2. Because there is so many different gate motors out there I honestly don’t know, generally it would go on to the Triger port. The controller has NC/NO and inching.(Which is a timer how long the pulse needs to be.) 3. Not sure if Alexa has custom commands because the device is seen as a switch so the command Gate ON would defiantly trigger it if the device was called Gate in ewelink then linked to Alex. Getting a gate installer in once you have the device configured would be recommended. Aleks This is not a Sonoff device but works in eWelink app and we have only had one return in 2 years

Hi, If you are just looking to open the gate with a pulse the gate controler would be most cost effactive but it will not give you a status. Its not a Sonoff products but it work with eWelink which would then be connected to you Alexa. https://www.sonoffafrica.co.za/product/ewelink-1ch-wifi-switch-inching-self-locking/ Coupon code Powerforum5% Aleks

Just inbox me you address and give me a few days and I will send a test rig to you. All you will have to do is plug it in. I will make it up with plug top and a extension. It will be fairly quick and we will have results with in 24 hours of pluging it in from the log files.

Hi, How are you? 1. 80% off the Sonoff devices are Wifi direct and just requier internet. Sonoff does have and RF range which requiers a RF bridge. They also have Zigbee range which require a Zigbee bridge the main diffrence is the Zigbee has status on the sensors and the RF doesn't. I personally belive that batteries in a permanent installation are a bad solution unless its invertor battery's and Sonoff sensors are not great on battery usage yet. 2. Unfortunately not. Sonoff mini is probably the only device with a Low voltage input on the S1 and S2. But I dont belive it would work unless you gate is on inverter power. 3. We have very little skill when comes to HA and our current focuse is on eWelink and Google. Its becomes very costly to support HA and I do believe next year our focus will start shifting. Aleks

Appolagies for that it was for @Scorp007 which we are still try to help with network issues. Aleks

Hi, I was so upset the day they announced the fee structure, I started removing it from our websites. We where actually in negotiations with them to sign up as a suppliers and the pricing was a $10k upfront and the $1 per user per year minimum 1000 users. Then they made changes and started charging users which killed the model for us as much as it reduced our costs it would be impossible for us to achieve our SA project. Aleks

Welcome to give me a call if you need🙂

I can put together a little test rig with a router, I can configure the router and a device and we can know if its GSM network in the area is a problem. I will have one in 3 days. The Huawei 3 Pro and I will run a test loop timer and we see what the results are at my place then we can move the rig to your place and then see what the log files and we can have some information to start the debug if you are keen. Note I will add the device to a test account and share it to you and we can see the log files and see if it drops and then we can start debugging from there Let me know if you are cool with that. Aleks

Hi Yes we have the Sonoff dual R3 which has a bilnd motor mode built in with interlock. https://www.sonoffafrica.co.za/product/sonoff-dual-r3-wifi-smart-switch/ PowerForum5% will give you 5% off Aleks

Hi Yes we do it would be the 4CH PRO. https://www.sonoffafrica.co.za/product/sonoff-4chpror3-wi-fi-smart-switch-with-rf-control/ PowerForum5% will give you 5% off Aleks

Hi You are welcome to buy from us and use coupone code "powerforum5%" https://www.sonoffafrica.co.za/ Aleks

Hi We are happy to give away a bundle pack which will include: 1x Sonoff Loadshedder or (if you don’t have a Invertor we can swap for L3 PRO) 1x Sonoff POWR320 Elite with display (will give you the ability to turn off the geyser) 1x Sonoff RGB Bulb which you can scene control to change colours with the Loadshedder which lets you know there load shedding 1x Sonoff 2CH Light Switch T0US2C (Introduction to smart lighting and scene control) 1x Sonoff Basic (for any other device you would like to use it on) Thank you for all you knowledge sharing on this forum and we will do these give- ways as often as we can. Aleks

Hi Good morning, yes sonoff have built in a feature on some of the device to gives you an alert after 5 minutes that the device is gone offline it works really well. It will be awesome when this can be used as a trigger. Not sure how long it will take them to get that feature finalized and going. Aleks

Hi Ewelink should not sign you out unless you logging through a different device, please feel free to give me a call tomorrow and we can defiantly debug the issue. I have to run and will be online tomorrow night. Aleks