SEGEN SOLAR

Hi Dewie, We would like to contact you to troubleshoot, please provide your contact details. Thank you,

Good day Munashe, Please will you kindly send me your contact details. I would like to investigate the matter. I apologize for any inconvenience caused. You are welcome to send it to me via [email protected] Thank you,

Good Day Frans The screen can potentially be woken up by an MCU firmware update. But to answer your question, Yes. We do have stock of the LCD control spares. The LCD board may need a firmware update to properly function in case it has an older firmware version. Usually indicated by an error Code 32 on the screen upon switching on. See attached application note on how to conduct a firmware update on your Kodak inverter with a link to the the latest Kodak Firmware versions. Let me know if this helps SR Application Note KODAK OG RANGE FIRMWARE UPDATE PROCEDURE (3).pdf

@nerezw Please read more on the Hubble weblink here: https://www.hubblelithium.co.za/about-the-cloudlink

Hi @TaliaB, Chris Radley is our company CEO. Please may I ask what this is regarding as I would be more than happy and willing to assist you with your query. Thanks!

Hi Scorp007, Please be advised the DC startup voltage for the 5.48 VMIII Inverter is 150v, you would need to add at least 1 more panel to reach the startup voltage.

Hi Johan, Sorry to hear about this, please may you send me the serial number of the unit so I can get someone on our side to assist you with this.

@Flouw, You are correct the Kodak OG6.2 does have 2 x Outputs. One for essential and one for non essential loads. The capability is basically 6.2 kW on either of them at anyone time or 6.2kW split proportionately at any given moment. So as long as you are not drawing more than a total of 6.2 kW at any given time through the inverter you are safe. You can however draw the full 6.2 kW through one output - as long as there is no draw at all from the secondary. I hope this answers your question. Regards, Nick

Hi Hennie, Please check if you are still measuring 48V DC after the fuse from the battery , if yes try and start the inverter with only AC connected to it. If the screen is still not coming on after checking please contact the Segen Technical team for further assistance.

Greetings Clair Gardner Thank you! Best, Daniel

Greetings Swannie Thank you for your inquiry. Please ensure the following: - parameter settings are set as per manual - dipswitch settings set accordingly - the pin outs on the cable be aligned Best, Daniel

Greetings Kampies Thank you for your contribution on the Power Forum. Please also log a Technical Enquiry off your Portal, should you need technical support. Our fantastic Technical Support Advisors are on standby to assist. Best, Daniel

Greetings ChrisC Please set your inverter to SUB, to ensure it is on solar first. This will ensure that you are not on bypass mode during the day. To log in the WatchPower app, please use the S/N number below the inverter. Best, Daniel

when close to your system can you kindly incorporate the below LCD settings: · Program 01 : SBU · Program 02: 100A ( maximum charge current from both your supplies which is your solar panels and utility) · Program 03: APL ( appliance default) · Program 05: PYL (Pylontech battery) · Program 06: LFE (Restart enable) · Program 07:EFE( Restart enable) · Program 09: 50Hz · Program 10 : 230V · Program 11: 40A ( this program is linked to program 2 so whatever value you used in program 2 will affect this program e.g., if the value in program 2 is less than the 1 for program 11 it will use program 2 for charging current so it’s better to have your program 11 current charge as low as possible as this current charge solely reflects on the utility charging current, because if not you would end up having a higher charge portion coming from the utility opposed to solar when charging your battery.) · Program 12: 49V safe voltage before reaching the lowest discharge voltage of 44.5V. · Program 13: 55V as per Pylontech data sheet · Program 16: is at your own discretion, you can choose what’s best for you for charging your battery. · Program 22 : AON (default settings) · Program 26 : 55V · Program 27: 55V · Program 29 :45V

Good day. This Setting can be achieved using Setting number 12 of the Unit. This Will cause the inverter to start charging the battery when it gets to the voltage level. The other option is to set the cut off Voltage on setting number 28. This will be done with voltage settings. Kodak inverters only have voltage settings and no Battery COC percentage values.